Skip to main content
Encore Moto
Workshop Notes

2003 950 Adventure Rebuild: Suspension

October 18, 2026

Why increase the suspension travel from 245mm to 270mm? I never had any ground clearance issues at 245mm, and it was already pretty tall from the factory as is. I never had a ride on the 950 Adventure S model, but I did own a 2010 KTM 990 Adventure R, which was sitting pretty at 265mm of travel, and that bike opened my eyes to a tall rally-spec suspension. Once I was back on my 950 at 245mm, I started investigating how I could make it handle and feel like the R. Short version: KTM lowering the Adventure’s ride height by modifying the suspension internals, without moving the swingarm pivot point, affects the original chassis design geometry. How much the bike’s performance is affected by this is semantics at my riding level, and if there is a difference, I can’t quantify it objectively. Point is, the science behind it makes sense to me, so I jacked up the suspension to get as close as I could to the original design intent of the good people at KTM who penned the KTM 950 Rally, destined to win at Dakar.

So now I have a desert camel, and when I pass truckers on the highway I can see what nudie magazines they’re reading. Mission accomplished! We used to joke, back when these bikes first came out, that tipping one into a corner on a paved road was like falling off a 6-foot wall, and that lane splitting around corners is the default setting because the bike takes up nearly two lanes when cranked over onto the side of the tyre. Surely this sounds familiar? Good times!

Here’s how we got to camel height.

I really wanted the 4K 270mm kit, but after seeing what import tax and shipping were going to cost me, the decision was made to go local and use MX/Enduro bike forks. The used forks were actually cheap since I was shopping for era-correct pieces, and that is how I ended up with a set of 2003 KTM 450 EXC Racing forks. It’s a gamble what condition the internals of a 23-year-old set of off-road forks are in. The fact that they were from the same year as my 950 gave me good vibes, and the internals were 100% usable. With the cash saved by going this route, I was able to get a set of Suspension101 gobblers through a friend in the States. These are basically adjustable valves for your forks that replace the originals.

We used the longer 14mm damping rods in these forks. The inner cartridge tubes on the KTM Enduro/MX bikes from this era are longer than the stock 950/990 units, so they are perfect as donor forks. The outer tubes on these bikes are shorter than the 950/990 outer tubes, so you have to use the original 950/990 outer tubes, which are 20mm longer, when doing this conversion. So you can run MX/Enduro inner tubes plus the longer damping rods, paired with 950/990 outer tubes. I worked with Mike Fuchs from Foximoto here in South Africa to do this, and the information I’m providing here is what I learnt from him during the process. We used the Yacugar progressive fork springs that were already in there, with a spacer bush to get the spring + spacer length we were aiming for.

Front end with carbon mudguard, fork and spoked wheel fitted
Two forks laid side by side to compare the used 450 EXC Racing forks against the originals
Fork tubes side by side during the build.
Pair of KTM Factory fork inner and outer tubes with the nitride coating, standing side by side
The tubes ready for assembly.
Close-up of the date stamp on a 450 EXC Racing fork axle clamp
The 450 EXC Racing axle clamps that replaced the 950 originals.
Close-up of the casting stamps on the other side of the 450 EXC Racing axle clamp
The 450 EXC Racing axle clamps that replaced the 950 originals.

The rear shock was much easier. Here we swapped in the H3 rebound shim, KTM part no. 50180161, which is the standard shim for the Adventure S models at 265mm of travel. Mike machined it down further to hit our shock travel target. We used a custom spring washer stack to achieve the correct rear spring preload at the new shock travel. The shock preload adjuster knob completely fell apart, so I reverse-engineered and 3D printed a replacement from ABS-GF, which is glass-filled ABS. I designed it for an interference fit so that it has zero play, and it came out great.

Close-up of the H3 rebound shim for the rear shock
The H3 rebound shim (KTM 50180161), machined for the 270mm travel target.
Stock OEM rear shock spacer before machining
The stock OEM spacer before machining. This is the part that will take the rear shock to 265mm of travel.

I had to source an S model side stand, and I removed the centre stand, as it was now the lowest point under the bike and way too short. Even with the S side stand she still leans too much, so maybe I’ll name her Eileen until I work out a better solution.

Encore Moto
Company
Trinity1 Business Systems (Pty) Ltd trading as Encore Moto
Registration Number: 2026/158290/07
Contact
Stellenbosch, South Africa
© 2026. All Rights Reserved.